Change or Reseal a Tub Drain
Everything You'll Need: A brand new drain stopper and flange (optional), a brand new drain shoe gasket (optional), mineral spirits, plumber's putty or silicone, a drain removal tool, an adjustable wrench (optional), a flathead screwdriver (optional) What It'll Cost: $15 to $20 for a fundamental stopper and flange assembly (per Grainger Industrial Supply -- including stopper) Everything You Could Save: $200 or more (a HomeWyse) How Long It Require: 30 to 60 minutes The way to Do It: This how-to covers only the drain flange (basket) and stopper. It doesn't address the drain shoe, nor the piping which connects your sewer line and your drain. Replacing these things may require moving your bathtub, putting a hole or tearing your shower . I've accommodated these measures from PlumbingSupply.com's guide on removing and replacing a drain flange. Unscrew your drain stopper and set aside (if not replacement ). Add your drain removal tool (drain key or smart barbell ) into the drain and then rotate counterclockwise until the drain flange pops out. In case the removal tools don't work, use a hair dryer to heat the drain flange and soften the plumber's putty or silicone holding the flange and base set up. Try again after a few minutes. Wash the drain hole and surrounding regions. Pat dry, then allow to air dry. Examine the shoe gasket. If the rubber is obviously worn out or it doesn't appear to be sealing tightly against the shoe any longer, use a flathead screwdriver to pop it out. If warranted replace the gasket. Press it against the screw thread to make a watertight seal. Apply plumber's putty at a ring on the underside of the new drain flange -- sufficient to create a complete seal with the tub. Put the flange and twist into the drain 's threads. Hand-tighten for your first couple of rotations, then use a drain removal application to tighten (clockwise) until there's only a little slack left. Use an adjustable wrench to your final quarter-turn. Don't overtighten -- this could squeeze the gasket out of place or crack the tub. Use mineral spirits to remove the putty of extra plumber from around the drain. Insert the existing or replacement stopper. Caution: Be sure to apply a liberal quantity of saline or plumber's putty . Inadequate coverage means leaks, which could wreak havoc on your bathroom flooring -- not to mention the ceilings and walls beneath. My dining room walls and ceilings sustained hundreds of dollars in entirely preventable water damage because the previous owner (or a contractor he hired) skimped on plumber's putty from the upstairs tub.
With rented or borrowed equipment, your DIY soul, and repeated how-to movie viewings, you can tackle these home plumbing repair and replacement jobs on your own.
Replace Faucet Fixtures
What You'll Need: Your faucet assembly, plumber's putty or silicone, a basin wrench (optional), mineral spirits, hex wrench (probably contained in the faucet assembly) What's 'll Cost: $30 to $40 for an easy chrome faucet; up of $400 to get a high-end version (per Home Depot) Everything You Can Save$60 to more than $500 (per HomeAdvisor) Long It Require: 60 to 90 minutes How to Do It: Replacing a faucet isn't as hard as it sounds. This explainer assumes you not replacing the sink, only the actual faucet assembly. It's adapted from the how-to of this Lowe : Close to the warm and cold valves. If the sink has no valves, switch off the key valve of your house . Open the hot and cold taps to drain any water in the lines. Unscrew the water lines or using a basin wrench. Disconnect the lift pole (the piece that opens and closes the drain). Remove the nuts at the base of the tap. Manually unscrew the plastic slip nut onto the P-trap (the bend in the drain line) and disconnect the drain flange. Sink holes and use mineral spirits or rust remover to wash around the drain. Put in a gasket at the base of this new faucet, if not already done. Insert the faucet into the mounting holes. Tighten the nuts. If not already done, install the faucet handles and tighten with a hex wrench (usually supplied ). Screw in the drain nut and fit closely with the bottom gasket (push or twist in). Employ screw on within the drain and plumber 's putty into the drain flange. Make sure that the flange hole faces backward. Further tighten the nuts and gasket. Install and test the drain pole assembly. Reconnect the distribution lines and operate the faucet. Assess for leaks and retighten in the entire assembly or reinstall necessary. Your faucet should include installation instructions. (How comprehensive they'll be is another matter.) Check with the latter where these instructions conflict with those provided by the producer. Caution: Faucets come in many different shapes and sizes. If at all possible, have your faucet assembly handy when you shop for your faucet. Purchasing the proper replacement will save you annoyance and time, go to
website.
Install an Automatic Dishwasher
Everything You'll Need: Your new dishwasher, a Philips head screwdriver, an adjustable wrench or pliers, electric tape, suitably sized screws, nuts, and the dishwasher 90 assembly (see your dishwasher's instructions for specific requirements) What It Cost: $200 for a simple dishwasher to over $1,000 to get a model What You Can Save: $100 to more than $500, depending on the sophistication of the Work and exactly what your plumber charges Long It'll Take: 90 to 120 minutes How to Do It: Installing a dishwasher is surprisingly simple. There are two catches that trip DIYers up: the dishwasher's weight and the prospect of working with electric wiring. In case you're match, here's exactly what You Have to perform (adapted from DIY Network's tutorial): Turn your home's power off at the breaker. Turn off the water at the sink, even if at all possible. If not, turn the water off at the line. Take the dishwasher out of the box and inspect against the sheet that is schematic that is included. Verify that everything is in the ideal place and everything the manufacturer says is included in the kit actually is. Uncap your home's dishwasher drain line and hook up to your dishwasher's drain outlet. Crimp the metal clamp (included) around the drain and thread through the hole to your own sink compartment. Position the dishwasher at its home compartment. Adjust its leg elevation using an adjustable wrench if needed. Fasten the dishwasher to the countertop with appropriately sized screws (probably provided in the kit). Attach the dishwasher's wiring into the local electricity inlet (like colors together). Screw on the wire nuts and cover with tape. Position the floor wire. Consult with the directions to be sure you of the manufacturer 've done this correctly. Hook the dishwasher's supply line to the dishwasher 90 (a special fresh water connection that you'll want to purchase separately) and twist. Attach the drain line. Turn on the water and power. Test a load and repeat these steps as required. Caution: This project requires some electrical work. If the idea of manipulating wiring makes you uneasy, in spite of your home's power off, save this one to the professionals.